4pcs TMC2130 পদবিন্যাস মোটর নীরব ড্রাইভার Stepstick ক্ষমতা Tube বিল্ট ইন ড্রাইভার বর্তমান 1.4 একটি শিখর বর্তমান 2.5 একটি প্রতিস্থাপন TMC2100
বৈশিষ্ট্য: ড্রাইভার capabitlity আপ টিপি 1.2 একটি(আরএমএস) continus কুণ্ডলী বর্তমান পদক্ষেপ/dir ইন্টারফেস সঙ্গে আপ 256 micristeps SPI ইন্টারফেস বা CFG পিনের জন্য কনফিগারেশন মোটর ভোল্টেজ: 5.5-45V যুক্তিবিজ্ঞান ভোল্টেজ: 3.3-5V Stealthchop - জন্য বেশ অপারেশন এবং মসৃণ গতি spreadCycle-অত্যন্ত গতিশীল, মোটর নিয়ন্ত্রণ কাটারী coolStep-বর্তমান contril জন্য engergy সঞ্চয় stallGuard-sensorless মোটর লোড সনাক্তকরণ dcStep-লোড নির্ভরশীল গতি নিয়ন্ত্রণ উল্লেখ্য: প্রতিটি শরীরের আছে শুধু স্ক্রু ড্রাইভার,আপনি যাতে আরো এবং আরো প্রয়োজন, স্ক্রু ড্রাইভার,pls আমাদের সাথে যোগাযোগ করুন. যদি না হয়,আমরা শুধুমাত্র আউট পাঠাতে এক. ভোক্তা শো ভিডিও : https://www.youtube.com/watch?v=yiHLwdAIApQ
যদি আপনি জানতে চান কিভাবে সেট TMC2130 stepper মোটর বর্তমান ,আপনি পাঠাতে পারেন ভোক্তা শো video:https://www.ইউটিউব.com/watch?v=0EH_hUJRLag
https://Channeldhaka.news/store/product/1pc-MKS-TMC2130-V1-1-Stepstick-Stepper-Motor-Driver-SPI-with-Heat-Sink-Ultra-silent-Excellent/3480083_32849988952.html?spm=2114.12010615.0.0.4f0e14f6LqDUio
এই আমাদের নতুন TMC2130 V1.1 জন্য এসপিআই
ট্যাগ: tmc2100, stepstick tmc2100, শিখর, সস্তা tmc2100, উচ্চ মানের stepstick tmc2100, চীন শিখর সরবরাহকারী.
Melville1987 2017-12-05 5/5 |
looks good, not tested yet. Delivered after 40 days. |
Ezkaza 34 2018-02-20 5/5 |
thank you. arrived quickly |
Jomarlugo 2018-01-23 3/5 |
Too slow & only 2 radiators with 4 drivers was in package. |
Vitalijgrigorjev 2018-01-24 3/5 |
okay, if you planning to buy this Fystec TMC2130 v1.0 driver as a direct replacement for your current A4988 or DRV8825 driver for your RAMPS 1.4 or MKS 1.4 board, i recommend STOP NOW and buy the original watterott TMC2130. why? because you need to fiddle with this driver in order to properly use them. but, if you have a lot experience with SMD soldering / desoldering, then fine you can buy this one. first of all, you need to desolder a small 0 ohm resistor in the chip (blue part of the image attached). next you need to solder a bridge at CFG4 and CFG5 (red/green part of image attached) in order to use StallGuard, StealthChop, and SpreadCycle PROPERLY in SPI mode. the solder bridging part, when done incorrectly, may DAMAGE / BREAK your board. after all of that, you need to desolder SCK, SDO, SDI, CS and NC pins on the Fystec TMC2130 board and reverse the SCK, SDO, SDI, and CS pins, then also reverse-connect the NC pin to the center most pin (black part of the image attached). |